TY - JOUR

T1 - Fracture locus characteristics of Al alloy 5083 processed by equal channel angular pressing using miniaturized specimens

AU - Melzer, Daniel

AU - Smirnov, Ivan

AU - Lukáš, Ondřej

AU - Dlouhý, Jaromír

AU - Evstifeev, Alexey

AU - Džugan, Ján

AU - Valiev, Ruslan

N1 - Funding Information: IVS and ADE acknowledge the support by Saint Petersburg State University (applied interdisciplinary research grant 2017, Activity 3, project id: 26130576 ), Russia. RZV acknowledges the support in part from the Ministry of Science and Higher Education of the Russian Federation under grant agreement No. 0838-2020-0006 . This was also supported from the Ministry of Industry and Trade of the Czech Republic in the form of institutional funding. Publisher Copyright: © 2021 Elsevier B.V.

PY - 2021/12/31

Y1 - 2021/12/31

N2 - After severe plastic deformation (SPD) processing, aluminum alloys show increased strength but low ductility. However, the ductility of the materials obtained during tensile tests does not reflect the full plastic deformation ability of the materials. This work presents the results of a more comprehensive plasticity analysis, which is applied first time to material after SPD processing. The current study considers an aluminum alloy 5083 before and after equal channel angular pressing (ECAP). The plasticity analysis was implemented based on the fracture locus, which was plotted in the space of the equivalent strain to fracture, the stress triaxiality parameter, and the Lode angle parameter using the Hosford–Coulomb (H–C) model. The parameters of the H–C model were determined using a combined experimental–numerical approach. It was found that the plasticity of the 5083 alloy strongly depended on a combination of the stress triaxiality and Lode angle parameter. However, the fracture locus of the material after ECAP processing showed slightly higher values of equivalent strain to fracture than that of the initial material. This approach makes it possible to estimate the ultimate plasticity of the materials after ECAP processing for a wide range of stress-strain states and can be used to predict fracture in plastic deformation processes.

AB - After severe plastic deformation (SPD) processing, aluminum alloys show increased strength but low ductility. However, the ductility of the materials obtained during tensile tests does not reflect the full plastic deformation ability of the materials. This work presents the results of a more comprehensive plasticity analysis, which is applied first time to material after SPD processing. The current study considers an aluminum alloy 5083 before and after equal channel angular pressing (ECAP). The plasticity analysis was implemented based on the fracture locus, which was plotted in the space of the equivalent strain to fracture, the stress triaxiality parameter, and the Lode angle parameter using the Hosford–Coulomb (H–C) model. The parameters of the H–C model were determined using a combined experimental–numerical approach. It was found that the plasticity of the 5083 alloy strongly depended on a combination of the stress triaxiality and Lode angle parameter. However, the fracture locus of the material after ECAP processing showed slightly higher values of equivalent strain to fracture than that of the initial material. This approach makes it possible to estimate the ultimate plasticity of the materials after ECAP processing for a wide range of stress-strain states and can be used to predict fracture in plastic deformation processes.

KW - Aluminum 5083

KW - Equal channel angular pressing

KW - Fracture locus

KW - Lode angle parameter

KW - Plasticity

KW - Plasticity methods

KW - Stress triaxiality

KW - CALIBRATION

KW - RUPTURE MECHANISMS

KW - COMBINED TENSION

KW - STRENGTH

KW - MECHANICAL-PROPERTIES

KW - DEFORMATION

KW - STRESS-TRIAXIALITY

KW - LODE PARAMETER

KW - MG

KW - DUCTILE FRACTURE

UR - http://www.scopus.com/inward/record.url?scp=85113985722&partnerID=8YFLogxK

UR - https://www.mendeley.com/catalogue/f482df06-4a8d-3013-bb31-21269bc5cedc/

U2 - 10.1016/j.jallcom.2021.161675

DO - 10.1016/j.jallcom.2021.161675

M3 - статья

AN - SCOPUS:85113985722

VL - 889

JO - Journal of Alloys and Compounds

JF - Journal of Alloys and Compounds

SN - 0925-8388

M1 - 161675

ER -