Shape memory effects in porous Ti - 45.0 at.% Ni alloy produced by self-propagating high-temperature synthesis

Natalia Resnina, Sergey Belyaev, Andrey Voronkov, Roman Badun

Research output: Contribution to journalArticleResearchpeer-review

2 Citations (Scopus)

Abstract

One way and two-way shape memory effects were studied on heating and cooling of preliminarily deformed porous Ti - 45.0 at.% Ni alloy produced by self-propagating high-temperature synthesis. The porous samples were initially deformed to different strains at a temperature of 25 °C and then they were subjected to heating and cooling through the temperature range of the martensitic transformations. The maximum given strain during preliminary deformation was 16% because further deformation of the sample resulted in porous sample failure. The results obtained have shown that the functional behavior of porous TiNi alloys differs from the properties of cast TiNi alloy. A strain recovery on heating due to the realization of the one-way shape memory effect, and a strain accumulation on cooling caused by a two-way shape memory effect, were observed if the preliminary strain was equal to 10% or higher. The dependencies of the values of one-way and two-way shape memory effects on preliminarily strain were non-linear; the strain increased significantly when the given strain rose from 7 to 14 %, and hardly changed if the given strain was larger than 14%.

Original languageEnglish
Pages (from-to)4690-4695
Number of pages6
JournalMaterials Today: Proceedings
Volume4
Issue number3PB
DOIs
StatePublished - 2017

Keywords

  • Martensitic transformation
  • Porous TiNi alloy
  • Self-propagating high-temperature synthesis
  • Shape memory effects
  • Strain recovery

Scopus subject areas

  • Materials Science(all)

Cite this

@article{462c6586c38b4df0b4e97e69063f1e8c,
title = "Shape memory effects in porous Ti - 45.0 at.{\%} Ni alloy produced by self-propagating high-temperature synthesis",
abstract = "One way and two-way shape memory effects were studied on heating and cooling of preliminarily deformed porous Ti - 45.0 at.{\%} Ni alloy produced by self-propagating high-temperature synthesis. The porous samples were initially deformed to different strains at a temperature of 25 °C and then they were subjected to heating and cooling through the temperature range of the martensitic transformations. The maximum given strain during preliminary deformation was 16{\%} because further deformation of the sample resulted in porous sample failure. The results obtained have shown that the functional behavior of porous TiNi alloys differs from the properties of cast TiNi alloy. A strain recovery on heating due to the realization of the one-way shape memory effect, and a strain accumulation on cooling caused by a two-way shape memory effect, were observed if the preliminary strain was equal to 10{\%} or higher. The dependencies of the values of one-way and two-way shape memory effects on preliminarily strain were non-linear; the strain increased significantly when the given strain rose from 7 to 14 {\%}, and hardly changed if the given strain was larger than 14{\%}.",
keywords = "Martensitic transformation, Porous TiNi alloy, Self-propagating high-temperature synthesis, Shape memory effects, Strain recovery",
author = "Natalia Resnina and Sergey Belyaev and Andrey Voronkov and Roman Badun",
year = "2017",
doi = "10.1016/j.matpr.2017.04.053",
language = "English",
volume = "4",
pages = "4690--4695",
journal = "Materials Today: Proceedings",
issn = "2214-7853",
publisher = "Elsevier",
number = "3PB",

}

Shape memory effects in porous Ti - 45.0 at.% Ni alloy produced by self-propagating high-temperature synthesis. / Resnina, Natalia; Belyaev, Sergey; Voronkov, Andrey; Badun, Roman.

In: Materials Today: Proceedings, Vol. 4, No. 3PB, 2017, p. 4690-4695.

Research output: Contribution to journalArticleResearchpeer-review

TY - JOUR

T1 - Shape memory effects in porous Ti - 45.0 at.% Ni alloy produced by self-propagating high-temperature synthesis

AU - Resnina, Natalia

AU - Belyaev, Sergey

AU - Voronkov, Andrey

AU - Badun, Roman

PY - 2017

Y1 - 2017

N2 - One way and two-way shape memory effects were studied on heating and cooling of preliminarily deformed porous Ti - 45.0 at.% Ni alloy produced by self-propagating high-temperature synthesis. The porous samples were initially deformed to different strains at a temperature of 25 °C and then they were subjected to heating and cooling through the temperature range of the martensitic transformations. The maximum given strain during preliminary deformation was 16% because further deformation of the sample resulted in porous sample failure. The results obtained have shown that the functional behavior of porous TiNi alloys differs from the properties of cast TiNi alloy. A strain recovery on heating due to the realization of the one-way shape memory effect, and a strain accumulation on cooling caused by a two-way shape memory effect, were observed if the preliminary strain was equal to 10% or higher. The dependencies of the values of one-way and two-way shape memory effects on preliminarily strain were non-linear; the strain increased significantly when the given strain rose from 7 to 14 %, and hardly changed if the given strain was larger than 14%.

AB - One way and two-way shape memory effects were studied on heating and cooling of preliminarily deformed porous Ti - 45.0 at.% Ni alloy produced by self-propagating high-temperature synthesis. The porous samples were initially deformed to different strains at a temperature of 25 °C and then they were subjected to heating and cooling through the temperature range of the martensitic transformations. The maximum given strain during preliminary deformation was 16% because further deformation of the sample resulted in porous sample failure. The results obtained have shown that the functional behavior of porous TiNi alloys differs from the properties of cast TiNi alloy. A strain recovery on heating due to the realization of the one-way shape memory effect, and a strain accumulation on cooling caused by a two-way shape memory effect, were observed if the preliminary strain was equal to 10% or higher. The dependencies of the values of one-way and two-way shape memory effects on preliminarily strain were non-linear; the strain increased significantly when the given strain rose from 7 to 14 %, and hardly changed if the given strain was larger than 14%.

KW - Martensitic transformation

KW - Porous TiNi alloy

KW - Self-propagating high-temperature synthesis

KW - Shape memory effects

KW - Strain recovery

UR - http://www.scopus.com/inward/record.url?scp=85020883084&partnerID=8YFLogxK

U2 - 10.1016/j.matpr.2017.04.053

DO - 10.1016/j.matpr.2017.04.053

M3 - Article

VL - 4

SP - 4690

EP - 4695

JO - Materials Today: Proceedings

JF - Materials Today: Proceedings

SN - 2214-7853

IS - 3PB

ER -